Knowledge and attitude of dentists toward implant retained restorations in Saudi Arabia

Objectives: The aim was to assess the knowledge and attitudes of specialists (SP) and general dental practitioners (GDP) toward cement‑retained restoration (CRR), screw‑retained restoration (SRR) and implant restorations in Saudi Arabia.Materials and Methods: Self‑designed‑structured questionnaires were distributed between SP and GDP by hand and through E‑mails. Opinion of dentists regarding factors vital in selection of CRR and SRR was enquired. Factors included esthetics, retrievability, retention, passive fit, fracture resistance, tissue health, cost‑effectiveness, fabrication ease, and required expertise. Participants also graded significance of treatment‑planning factors for implant‑retained prosthesis. Analysis of comparative response frequencies and significance grades was done using the Chi‑square and independent t‑test.Results: Of 552 respondents, 64% were SP and 36% were GDP with overall response rate of 67%. About 75% of SP and 80% of GDP used SRR in <50% and <25% of their implant practice respectively. The opinion of GDP and SP was significantly different with regards to esthetics, fabrication ease, retrievability, retention and cost‑effectiveness between CRR and SRR (P < 0.05). Overall, CRR were considered better in terms of esthetics, passive fit, fabrication ease, required expertise and fracture resistance. However, SRR were regarded as having better retention, retrievability, soft tissue health and cost‑effectiveness. The average significance scores were significantly higher for SP as compared to GDP for six out of nine factors.Conclusions: Knowledge of SP and GDP for selection of implant‑retained restorations was broadly in line with standard evidence. The clinical use of CRR was greater in comparison to SRR.Key words: Cement‑retained, implants retained restorations, knowledge, screw‑retaine

The suppression of magnetism and the development of superconductivity within the collapsed tetragonal phase of Ca0.67Sr0.33Fe2As2 at high pressure

Structural and electronic characterization of (Ca0.67Sr0.33)Fe2As2 has been performed as a func- tion of pressure up to 12 GPa using conventional and designer diamond anvil cells. The compound (Ca0.67Sr0.33)Fe2As2 behaves intermediate between its end members-CaFe2As2 and SrFe2As2- displaying a suppression of magnetism and the onset of superconductivity. Like other members of the AEFe2As2 family, (Ca0.67Sr0.33)Fe2As2 undergoes a pressure-induced isostructural volume collapse, which we associate with the development of As-As bonding across the mirror plane of the structure. This collapsed tetragonal phase abruptly cuts off the magnetic state, giving rise to superconductivity with a maximum Tc=22.2 K. The maximum Tc of the superconducting phase is not strongly correlated with any structural parameter, but its proximity to the abrupt suppression of magnetism as well as the volume collapse transition suggests that magnetic interactions and structural inhomogeneity may play a role in its development. The pressure-dependent evolution of the ordered states and crystal structures in (Ca,Sr)Fe2As2 provides an avenue to understand the generic behavior of the other members of the AEFe2As2 family.Comment: 9 pages, 9 figure

Dietary Self-Selection by Laying Hens Offered Choices of Feed

A short telm dietary self-selection experiment (28 days) was conducted with laying hens fed three treatments (Tl-T3) consisting of a commercially available layer feed (1'1, single choice), commercially available layer feed and oyster shell grit offered separately (T2, two choices) and a com mixture, soyabean meal mixture and oyster shell grit offered sejJarately (T3, three choices). Measurement of feed intake was divided into three feeding periods, from 0800-1200h, 1200-1600h and 1600-0800h. Feed and water' were available ad Ii bitum. Hens were raised under' 15 hour Photo period. Feed, energy and protein intakes were significantly better' on the commercial diet and lower in the other' two treatments. Calcium intake was significantly lower on the single choice and three choice diets. In all treatments, the hens tended to consume more feed during the pel10d between 1600-0800h (40.8-45.8% feed consumed), that is very late in the evening and very early in the morning. Similar amounts of feed (26.2-29.7% of feed consumed) were consumed between 0800-1200h and 1200-1600h. egg production, egg mass and feed conversion were significantly better' on the two and three-choice diets as compared to the single diet. There was no difJeI'ence in egg weight among the three treatments

Developing the Surface Chemistry of Transparent Butyl Rubber for Impermeable Stretchable Electronics

Transparent butyl rubber is a new elastomer that has the potential to revolutionize stretchable electronics due to its intrinsically low gas permeability. Encapsulating organic electronic materials and devices with transparent butyl rubber protects them from problematic degradation due to oxygen and moisture, preventing premature device failure and enabling the fabrication of stretchable organic electronic devices with practical lifetimes. Here, we report a methodology to alter the surface chemistry of transparent butyl rubber to advance this material from acting as a simple device encapsulant to functioning as a substrate primed for direct device fabrication on its surface. We demonstrate a combination of plasma and chemical treatment to deposit a hydrophilic silicate layer on the transparent butyl rubber surface to create a new layered composite that combines Si-OH surface chemistry with the favorable gas-barrier properties of bulk transparent butyl rubber. We demonstrate that these surface Si-OH groups react with organosilanes to form self-assembled monolayers necessary for the deposition of electronic materials, and furthermore demonstrate the fabrication of stretchable gold wires using nanotransfer printing of gold films onto transparent butyl rubber modified with a thiol-terminated self-assembled monolayer. The surface modification of transparent butyl rubber establishes this material as an important new elastomer for stretchable electronics and opens the way to robust, stretchable devices

Diurnal and seasonal variations of <i>hm</i>F2 deduced from digitalionosonde over New Delhi and its comparison with IRI 2001

International audienceUsing digital ionosonde observations at a low mid-latitude station, New Delhi (28.6°N, 77.2°E, dip 42.4°N), we have derived hourly monthly values of hmF2 (the real height corresponding to the peak electron density in the F2-region), employing both the Dudeney (1983) and Bilitza (1990) empirical formulations for the period from January 2001 to August 2002. The diurnal and seasonal variations of hmF2 are analyzed. Further, to assess the predictability of the latest available model, International Reference Ionosphere, (IRI-2001), we have obtained the median values of hmF2 derived from M(3000)F2 for each hour during different seasons and compare these with the model. Our results show that both the Dudeney (1983) and Bilitza (1990) formulations reveal more or less a similar diurnal trend of hmF2, with higher values around midnight and lower during sunrise, in all the seasons. It is also noted that the hmF2 shows a larger variability around midnight than by daytime, in all the seasons. Further, the study shows that median values of observed hmF2, using both formulations, are somewhat larger than those predicted by the IRI, in all seasons and at all local times. During summer, the IRI values agree comparatively well with the observations, especially during daytime. Major discrepancies occur when the IRI underestimates observed hmF2 for local times from about 14:00 LT to 18:00 LT and 04:00 LT to 05:00 LT during winter and equinox, where the percentage deviation of the observed hmF2 values with respect to the IRI model varies from 15 to 25%. The difference between the model and observations, outside this time period, remains less than 20% during all the seasons. Key words. Ionosphere (modelling and forecasting; equatorial ionosphere